Maker Pro
Maker Pro

811A's, Dual Grid and Class B triodes

I was browsing through Terman (2nd edition) last night and read a
paragraph about "Dual Grid and Class B triodes". According to Terman,
if two concentric (but similar pitch) grids are put in the triode and
then connected to each other as a single control grid, the result is a
high-mu triode that needs zero bias for Class B operation.

I do not see dual-grid tubes mentioned in Terman's 3rd edition in the
same way.

Googling the term, I see that the 52 tube seems to be an example where
both grids are brought out to individual terminals.

I also see that sometimes "dual grid" is used to describe RF tubes
where there are two pins for a single grid (to decrease inductance I
guess), I'm not talking about these tubes.

The two-grids-connected-together characteristics remind me a lot of,
for example, the 811A (the most familiar Class B triode I'm familiar
with), but that only has a single grid terminal. Am I correct that the
internal grid structures of an 811A are essentially that of two
connected grids? If not, what inside an 811A makes it zero-bias high-
mu class B triode, as opposed to say its externally similar non-
identical-twin the 812A (a low-to-medium-mu triode that needs bias)?

I also note that Terman claims that the dual-grid structure forms a
very good electrostatic shield between heater and plate, and see that
811A's are often used in grounded-grid connection in RF amps. (Must be
a bitch to neutralize in common-cathode).

I've been intermittently playing around with SPICE to model 811A
curves (including grid current at positive grid voltage) and none of
the conventional triode models work right at all - its curves are more
like a pentode (in fact it's pretty trivial to fit it this way if you
let the diode characteristics take over at low plate voltage).

Tim.
 
E

Ed Engelken

Jan 1, 1970
0
Googling the term, I see that the 52 tube seems to be an example where
both grids are brought out to individual terminals.
=======================================
The #46 is another. The 46 was popular in a number of Atwater Kent
radios circa 1932-33. Class B Push-Pull output stages in high-end
radios had a brief run in the early 1930s, then faded into history. --
Ed
 
T

Tim Wescott

Jan 1, 1970
0
I was browsing through Terman (2nd edition) last night and read a
paragraph about "Dual Grid and Class B triodes". According to Terman,
if two concentric (but similar pitch) grids are put in the triode and
then connected to each other as a single control grid, the result is a
high-mu triode that needs zero bias for Class B operation.

I do not see dual-grid tubes mentioned in Terman's 3rd edition in the
same way.

Googling the term, I see that the 52 tube seems to be an example where
both grids are brought out to individual terminals.

I also see that sometimes "dual grid" is used to describe RF tubes
where there are two pins for a single grid (to decrease inductance I
guess), I'm not talking about these tubes.

The two-grids-connected-together characteristics remind me a lot of,
for example, the 811A (the most familiar Class B triode I'm familiar
with), but that only has a single grid terminal. Am I correct that the
internal grid structures of an 811A are essentially that of two
connected grids? If not, what inside an 811A makes it zero-bias high-
mu class B triode, as opposed to say its externally similar non-
identical-twin the 812A (a low-to-medium-mu triode that needs bias)?

I also note that Terman claims that the dual-grid structure forms a
very good electrostatic shield between heater and plate, and see that
811A's are often used in grounded-grid connection in RF amps. (Must be
a bitch to neutralize in common-cathode).

I've been intermittently playing around with SPICE to model 811A
curves (including grid current at positive grid voltage) and none of
the conventional triode models work right at all - its curves are more
like a pentode (in fact it's pretty trivial to fit it this way if you
let the diode characteristics take over at low plate voltage).

Tim.
Dual-grid tubes were popular for a short while. They were touted as
being versatile -- connect grid 2 to grid 1 and you had a high-mu
triode, connect grid 2 to the plate and you had a low-mu triode.
Judging from my tube data books, it didn't take folks long to decide
they just wanted one or the other, not two in one package.

The curves look pretty triode-like to me, once you take into account the
fact that the thing is running almost exclusively at positive grid
voltages. Perhaps the SPICE triode models aren't taking this into account?

--

Tim Wescott
Wescott Design Services
http://www.wescottdesign.com

Posting from Google? See http://cfaj.freeshell.org/google/

Do you need to implement control loops in software?
"Applied Control Theory for Embedded Systems" gives you just what it says.
See details at http://www.wescottdesign.com/actfes/actfes.html
 
T

tubegarden

Jan 1, 1970
0
=======================================
The #46 is another. The 46 was popular in a number of Atwater Kent
radios circa 1932-33.  Class B Push-Pull output stages in high-end
radios had a brief run in the early 1930s, then faded into history.  --
Ed

Hi RATs!

I have a huge P-P 46 vintage amp. It is not yet functioning. It is
clearly very well built :)

Grow up, Class "A" does not mean good, it means simple ... which,
despite some journalists' daydreams, is not exactly the same
thing ...

Happy Ears!
Al
 
Hi RATs!

I have a huge P-P 46 vintage amp. It is not yet functioning. It is
clearly very well built :)

Grow up, Class "A" does not mean good, it means simple ... which,
despite some journalists' daydreams, is not exactly the same
thing ...

A push-pull pair of zero-bias class B triodes is even more remarkably
simple.

When I first saw the schematic of a 811A P-P audio amp, I was
astonished to find not a single resistor or capacitor in the circuit.
Two tubes, input and output transformers, and connections to a
filament supply and a plate supply. That's all there is, folks!

Tim.
 
B

Bret Ludwig

Jan 1, 1970
0
This is very true and interesting. RCA figured out you could strap
the control and screen grids of certain power pentodes and use them as
low or zero bias triodes, and a couple of RCA theater amps do this.
This is also seen in AM era editions of the W6SAI Radio Handbook for
modulators. It is simple. It works. Based on long time experiments it
was concluded it doesn't sound very good at all.

I have never tried it, on the theoryu if it worked very well it would
be popular.

The 811 is certainly an attractive tube economically. It has a mu of
160 as I remember. The Altec 1570B used them as did the Gotham Audio
cutter head amp using a GR toroid for output.
 
R

RapidRonnie

Jan 1, 1970
0
This is very true and interesting. RCA figured out you could strap
the control and screen grids of certain power pentodes and use them as
low or zero bias triodes, and a couple of RCA theater amps do this.
This is also seen in AM era editions of the W6SAI Radio Handbook for
modulators. It is simple. It works. Based on long time experiments it
was concluded it doesn't sound very good at all.

Several of the last of the RCA MI-series cinema amps did this with
6L6s and I believe 6146s. None are desireable to the audiophile in
stock form.
I have never tried it, on the theory if it worked very well it would
be popular.

The 811 is certainly an attractive tube economically. It has a mu of
160 as I remember. The Altec 1570B used them as did the Gotham Audio
cutter head amp using a GR toroid for output.

They showed why toroids are a bad idea for opt's very well, although
there are still a lot of people not listening. With a conventional or
C-core transformer and a revised feedback loop the basic design is
well worth study, though.

The 811 can be substituted in the MI200 McIntosh if the proper
intermediate transformer is put in so as to get the filament voltage
at the 6.3 rather than the 10 volts of the, I think, 8005s. Although
the amplification factor of the 811 is way too high it works anyway.
Distortion still meets Mc specs. We wound one, in fact, where I worked
on a toroid, because we had plenty of scrap surplus transformers we
could dewind (and take the copper home.) And a Gorman winder, which
makes winding toroids pretty fast and simple. The 811s pull more
current but the Mc filament transformers never even got hot.
 
R

RapidRonnie

Jan 1, 1970
0
=======================================
The #46 is another. The 46 was popular in a number of Atwater Kent
radios circa 1932-33. Class B Push-Pull output stages in high-end
radios had a brief run in the early 1930s, then faded into history. --
Ed

Because using conventional circuits the distortion was terrible. True
Class B operation works well only at high continuous levels without
extreme measures such as Wiggins and Mcintosh/Gow/Corderman afforded.
Al Bereskin at Baldwin designed the "poor man's Mc" for organ use and
it was published in an extremely good DIY article in the IRE journal
in '55 or '56. It never got below 2% THD.
 
I

Ian Iveson

Jan 1, 1970
0
Bugger... HTML.

Al said:
....
Grow up, Class "A" does not mean good, it means simple ... which,
despite some journalists' daydreams, is not exactly the same
thing

*Saxophones are really complicated.

cheers, Ian.
 
J

Jim Mueller

Jan 1, 1970
0
The dual grid tubes strike me as a gimmick. Any pentode or beam power tube
can be connected at least 4 ways. Connect the screen to B+ and it behaves
as a pentode or beam power tube. Connect the screen to the control grid and
it becomes a high-mu triode. Connect the screen to the plate and it becomes
a low-mu triode. Connect the control grid to a low positive voltage and
drive the screen and it is a space charge triode.

The 811 has only one grid as do other zero bias tubes like the 6N7 and 1635.
They just wound the grid with many turns spaced close together to get this
characteristic. Low-mu tubes like the 812, 2A3, and 12B4 have few turns
spaced far apart. The only triode I know of with two grids is the 6C5. The
second grid is internally connected to the plate.

I have seen circuits using 6V6s with the screen tied to the control grid to
make a zero bias triode.

The old ARRL handbooks (50s?, 60s?) had a listing in their tube tables for
using a 12AX7 as a class B zero bias output tube. They said it could
produce 7.5W. I never saw a circuit that actually used one this way,
however.
 
U

Uncle Peter

Jan 1, 1970
0
RapidRonnie said:
Because using conventional circuits the distortion was terrible. True
Class B operation works well only at high continuous levels without
extreme measures such as Wiggins and Mcintosh/Gow/Corderman afforded.
Al Bereskin at Baldwin designed the "poor man's Mc" for organ use and
it was published in an extremely good DIY article in the IRE journal
in '55 or '56. It never got below 2% THD.
Most of those sets used push-pull class A, not B.

Pete
 
K

ken scharf

Jan 1, 1970
0
The two-grids-connected-together characteristics remind me a lot of,
for example, the 811A (the most familiar Class B triode I'm familiar
with), but that only has a single grid terminal. Am I correct that the
internal grid structures of an 811A are essentially that of two
connected grids? If not, what inside an 811A makes it zero-bias high-
mu class B triode, as opposed to say its externally similar non-
identical-twin the 812A (a low-to-medium-mu triode that needs bias)?
There is more than one way to skin a cat. The 811A is a high mu triode.
There are several ways to create such a beast.

One: place the grid closer to the cathode than to the plate. The ratio
of the distance between grid and cathode vs the distance between cathode
and plate is one of the factors that determine the mu of a triode.

Two: construct the grid with close spaced turns. The closer the turns
of the grid wires are to each other, the higher the mu.

Three: Use two concentric grids. This is very similar to number two.
I also note that Terman claims that the dual-grid structure forms a
very good electrostatic shield between heater and plate, and see that
811A's are often used in grounded-grid connection in RF amps. (Must be
a bitch to neutralize in common-cathode).
ANY triode works well in grounded grid. A high mu triode will have
better screening due to the close wound grid. Tetrodes such as the
4-400 have been used in grounded grid by grounding both grids. Others
such as the 4cx250 don't have enough heavy enough grids to handle the
current in class AB2 or B so they are run in cathode driven service with
normal grid and screen voltages, but with both grid and screen grounded
for RF.
 
Top