Maker Pro
Maker Pro

Building a ~15V 70A VCCS

A

Andy Neillans

Jan 1, 1970
0
Hi all,

I'm looking at building a Voltage Controlled Current Source; approx 15V
output, with up to 70A available - I need to be able to control the
current.

I've found this schematic (http://www.neillans.co.uk/VCCS1.pdf), and if
I were to uprate all the components (e.g. from 1/4W resistors to 1W or
higher), and replaced the IRFZ48Vs with the IRFZ48Ns which have a
higher current load, would it work?
I tried to build + simulate this circuit in EWB, but it didn't work out
- but that could be down to my VHDL :)

I've been working with electronics etc for years, but never ventured
far from digital solutions, although I have knocked up power supplies
in the past, they have never been VCCS.

Please Help :)

Andy
 
P

Phil Allison

Jan 1, 1970
0
"Andy Neillans"
I'm looking at building a Voltage Controlled Current Source; approx 15V
output, with up to 70A available - I need to be able to control the
current.

I've found this schematic (http://www.neillans.co.uk/VCCS1.pdf), and if
I were to uprate all the components (e.g. from 1/4W resistors to 1W or
higher), and replaced the IRFZ48Vs with the IRFZ48Ns which have a
higher current load, would it work?


** Ummmm.


15 volts at 70 amps = 1050 watts of dissipation in the mosfet bank, worst
case.

I reckon that might take 35 of them, 2 amps apiece on a whopper heatsink.

The PSU will be a treat as well.



.......... Phil
 
A

Andy Neillans

Jan 1, 1970
0
Phil said:
15 volts at 70 amps = 1050 watts of dissipation in the mosfet bank, worst
case.

Correct; planning on building it up as multiple large heatsinks, which
are actually copper water cooled.

The PSU will usually only run at around 12 - 15V @ 40 - 50A (so peek of
750W), although I need the extra capacity to be available. I'm also
planning on expanding the system as time goes on with additional units
to increase the current availability.

The PSU's are to be used for electroplating aluminium at the company I
work for, and they will be expected to run for around 8 hours a day
under the above load (another reason why I'm over-specing).

Andy
 
K

Ken Smith

Jan 1, 1970
0
Hi all,

I'm looking at building a Voltage Controlled Current Source; approx 15V
output, with up to 70A available - I need to be able to control the
current.

Since you didn't say you needed more than one nor how good it really has
to be:

How about just buying an off line switcher power supply that has a
remotely programmed current limit and running it at the current limit all
the time? I'd look for a product like:

http://www.xantrex.com/web/id/79/p/1/pt/20/product.asp
 
R

Rich Grise

Jan 1, 1970
0
Correct; planning on building it up as multiple large heatsinks, which
are actually copper water cooled.

The PSU will usually only run at around 12 - 15V @ 40 - 50A (so peek of
750W), although I need the extra capacity to be available. I'm also
planning on expanding the system as time goes on with additional units
to increase the current availability.

The PSU's are to be used for electroplating aluminium at the company I
work for, and they will be expected to run for around 8 hours a day
under the above load (another reason why I'm over-specing).

You should look around for a "carbon pile". It's just a big huge
honking power resistor that you adjust by cranking down on a
pressure screw - one of those should have no problem handling
only 70 amps. As long as your supply is stable, you should be
able to set it and forget it.

Plus, I'd have to have this corroborated by somebody who knows
their elbow from a SMPS - but would PWM control work for plating?

Thanks,
Rich
 
A

Andy Neillans

Jan 1, 1970
0
Hi all,

Thanks for the advice so far - its appreciated :)
The schematic is getting there - just one last question.

I've come across a lot of advice to put a resistor and capacitor in
parallel to the tansformers primary coils in order to help regulate the
fluctuations between the mulitple transformers - however, how do you
calculate the required values?

I'm going to be using 4 x 500VA tordial transformers, with 240V primary
windings, with two secondary windings of 25V @ 10A. The secondaries
will be connected in parallel to provide the required amperage, and
there will be two 56000mF electrolytic capacitors to smooth the output
connected in parallel. The primaries will be connected in parallel to
the same 240V A/C source (suitably fused etc).

Any advice on the method to calculate the required resistors + caps on
the primary windings ?

Andy
 
P

Phil Allison

Jan 1, 1970
0
"Andy Neillans"
I've come across a lot of advice to put a resistor and capacitor in
parallel to the tansformers primary coils in order to help regulate the
fluctuations between the mulitple transformers - however, how do you
calculate the required values?

** Name the source of that advice.

I could do with a good belly laugh.


I'm going to be using 4 x 500VA tordial transformers, with 240V primary
windings, with two secondary windings of 25V @ 10A. The secondaries
will be connected in parallel to provide the required amperage, and
there will be two 56000mF electrolytic capacitors to smooth the output
connected in parallel. The primaries will be connected in parallel to
the same 240V A/C source (suitably fused etc).

** Better fuse each tranny separately.

Any advice on the method to calculate the required resistors + caps on
the primary windings ?


** Someone is having a "lend" of you.

The scary bit is that you are so gullible you believe it.

Transformer theory a bit shaky is it ??



.......... Phil
 
A

Andy Neillans

Jan 1, 1970
0
Hi Phil,
** Name the source of that advice.

I could do with a good belly laugh.

I thought it was a bit insane too, but hey, I've never parallelled
transformers, so ....
** Better fuse each tranny separately.

Already am :)
** Someone is having a "lend" of you.

The scary bit is that you are so gullible you believe it.

Transformer theory a bit shaky is it ??

Very - see above :) Thought I'd post, just to make sure though, as I
was planning on leaving them out. Just didn't want to possibly risk
damaging the tordials.

Cheers for replying tho :)

Andy
 
J

John Larkin

Jan 1, 1970
0
Hi all,

I'm looking at building a Voltage Controlled Current Source; approx 15V
output, with up to 70A available - I need to be able to control the
current.

I've found this schematic (http://www.neillans.co.uk/VCCS1.pdf), and if
I were to uprate all the components (e.g. from 1/4W resistors to 1W or
higher), and replaced the IRFZ48Vs with the IRFZ48Ns which have a
higher current load, would it work?
I tried to build + simulate this circuit in EWB, but it didn't work out
- but that could be down to my VHDL :)

I've been working with electronics etc for years, but never ventured
far from digital solutions, although I have knocked up power supplies
in the past, they have never been VCCS.

Please Help :)

Andy

Does plating need filtered DC? You might consider a big transformer
driving a packaged SCR bridge rectifier puck thingoe, with a primary
circuit breaker and a huge output series resistor as the ultimate
protection/current limit. That would be simple, low loss, and
practically indestructable.

The multiple-fet thing could turn out to be an immense headache for
the relatively inexperienced... envision coffee cups full of exploded
fets and plating lines down for days at a time.

Best yet, buy a commercial plating supply.

John
 
D

Don Foreman

Jan 1, 1970
0
Does plating need filtered DC?

I've read that chrome works best with low ripple, though many
commercial plating supplys employ no filtering at all.
Best yet, buy a commercial plating supply.

Pricey! Absurdly so, for what they contain.
 
J

John Larkin

Jan 1, 1970
0
I've read that chrome works best with low ripple, though many
commercial plating supplys employ no filtering at all.


Pricey! Absurdly so, for what they contain.


How much would a plating supply like that cost?

It's really hard to design your own gear and come out ahead of a
commercial product. If it's expensive, there's usually a reason.

I wouldn't build my own DVM, oscilloscope, TV, or bench power
supply... It's just not worth my time, usually by a huge factor.

We see a lot of posts here by people, usually beginners, who think
they can build one-piece electronics cheaper than they can buy it. I
think that's seldom true.

John
 
A

Andy Neillans

Jan 1, 1970
0
Does plating need filtered DC?
I've read that chrome works best with low ripple, though many
commercial plating supplys employ no filtering at all.

We plate a lot of different finishes, including chrome but also basic
dyed anodisation - the best results always come from a fairly ripple
free supply - any ripple changes the thickness of the layer, and
although we are talking microns, it can make a massive impact on the
end result.
Pricey! Absurdly so, for what they contain.

I did get a quote for a unit for this. And it was over a thousand
pounds. With a 5 month lead time.
The cost could be bearable, but the lead time certainly is not. And we
wouldn't have as much control over the system - it could end up that we
add additional production lines, tanks etc, so need more PSU's - rather
build them in house instead of coughing up large sums and waiting an
eternity.

Andy
 
D

Don Foreman

Jan 1, 1970
0
How much would a plating supply like that cost?

It's really hard to design your own gear and come out ahead of a
commercial product. If it's expensive, there's usually a reason.

I wouldn't build my own DVM, oscilloscope, TV, or bench power
supply... It's just not worth my time, usually by a huge factor.

We see a lot of posts here by people, usually beginners, who think
they can build one-piece electronics cheaper than they can buy it. I
think that's seldom true.

John

See
http://www.caswellplating.com/kits/rect.htm

Start at $1686 because the slope front jobs have no filtering at all;
they're just xfmrs, variacs and rectifiers.

None of these are voltage controlled AFAIK. They're all adjusted by
turning a knob.

Here is a suitable transformer for $110:
http://tinyurl.com/8o8ur

Add rectifiers for maybe another $100 (being generous)
http://tinyurl.com/cdhtq

The brute-force water-cooled MOSFET regulator would do the rest.
IRF1404 is rated at 162 amps at 40 volts, $3.80 ea from Digi-Key. .
Thermal considerations would require using several of these in
parallel so figure 30 to 50 bux worth of MOSFET's. We're now up to
$250 -- time spent screwing around being free, of course. Control
cctry would be trivial, perhaps another $25. The OP already
contemplates the humongous heatsink.

Oh, I forgot filter caps. Threephase would be a lot better here
because then you could skip the filter caps though you'd need more
(but smaller) transformers and more rectifiers.

Figure at least 100,000 uF of capacitor here. 68,000 uF at 25 WVDC
are $21.43 ea at Digi-Key. I'd go with several 22,000 uF 40 WVDC
caps at $18.77 ea. to handle the ripple current better. 10 of 'em
(220,000 uF total) are about $175. Total now is still <$500.

Brute force approach, you'll need a hawg of a current sense resistor,
lots of ways to do that.

This unit would be voltage-controllable from 0 to 70 amps, it's
output ripple would be milliamps and it would be immune to short
circuits.
 
J

John Larkin

Jan 1, 1970
0
See
http://www.caswellplating.com/kits/rect.htm

Start at $1686 because the slope front jobs have no filtering at all;
they're just xfmrs, variacs and rectifiers.

None of these are voltage controlled AFAIK. They're all adjusted by
turning a knob.

Here is a suitable transformer for $110:
http://tinyurl.com/8o8ur

Add rectifiers for maybe another $100 (being generous)
http://tinyurl.com/cdhtq

The brute-force water-cooled MOSFET regulator would do the rest.
IRF1404 is rated at 162 amps at 40 volts, $3.80 ea from Digi-Key. .
Thermal considerations would require using several of these in
parallel so figure 30 to 50 bux worth of MOSFET's.

That's a TO-220 rated at 202 amps DC, 333 watts dissipation. If the OP
(or anybody else) believes these numbers, he's in for some serious
pain.

Note the derating factor of 2.2 watts/degC. Then note the thermal
resistances. Then read the footnotes. Why does IR *do* this? Do they
want their fets to explode?

TO-247's, directly bolted to a water-cooled sink with silicone grease,
no insulator, not too close together, might prudently be used at 100
wats each or so.

We're now up to
$250 -- time spent screwing around being free, of course. Control
cctry would be trivial, perhaps another $25. The OP already
contemplates the humongous heatsink.

Oh, I forgot filter caps. Threephase would be a lot better here
because then you could skip the filter caps though you'd need more
(but smaller) transformers and more rectifiers.

Figure at least 100,000 uF of capacitor here. 68,000 uF at 25 WVDC
are $21.43 ea at Digi-Key. I'd go with several 22,000 uF 40 WVDC
caps at $18.77 ea. to handle the ripple current better. 10 of 'em
(220,000 uF total) are about $175. Total now is still <$500.

No packaging, no heatsink/plumbing, no switches/fuses/breakers, no
loss-of-water cutout, no meters, no labor cost.
Brute force approach, you'll need a hawg of a current sense resistor,
lots of ways to do that.

Just apply time and money.
This unit would be voltage-controllable from 0 to 70 amps, it's
output ripple would be milliamps and it would be immune to short
circuits.

It would be a serious project. SCRs would be simpler and a lot safer.
There are cheap trigger boards around, packaged SCR bridges, stuff
like that. 3-phase would be nice... no filters.

John
 
D

Don Foreman

Jan 1, 1970
0
That's a TO-220 rated at 202 amps DC, 333 watts dissipation. If the OP
(or anybody else) believes these numbers, he's in for some serious
pain.

Note the derating factor of 2.2 watts/degC. Then note the thermal
resistances. Then read the footnotes. Why does IR *do* this? Do they
want their fets to explode?

TO-247's, directly bolted to a water-cooled sink with silicone grease,
no insulator, not too close together, might prudently be used at 100
wats each or so.

Right! That's why I recommended using 10 of them.
No packaging, no heatsink/plumbing, no switches/fuses/breakers, no
loss-of-water cutout, no meters, no labor cost.

I stipulated that heatsink-related issues were "given" per OP's post,
and that cost of labor was not included. I think that's the OP's
intent: to use available in-house labor to reduce cashflow cost.
Just apply time and money.


It would be a serious project. SCRs would be simpler and a lot safer.
There are cheap trigger boards around, packaged SCR bridges, stuff
like that. 3-phase would be nice... no filters.

Fooey! Please say more about how SCR's would be safer -- or simpler
for that matter. I don't think so. Please show sources and prices
for the cheap trigger boards and packaged SCR bridges that you
mention -- and how these might be assembled to meet the OP's request.

Even with 3 phase excitation there's no way they'll strip ripple like
a series-pass bank of MOSFET's would. That flat isn't on with SCR's.

This is not a "serious project" if the OP can do the watercooled
heatsink he said he could. Please show how doing it with SCR's
would be simpler, even with significantly inferior performance.
 
D

Don Foreman

Jan 1, 1970
0
I did get a quote for a unit for this. And it was over a thousand
pounds. With a 5 month lead time.
The cost could be bearable, but the lead time certainly is not. And we
wouldn't have as much control over the system - it could end up that we
add additional production lines, tanks etc, so need more PSU's - rather
build them in house instead of coughing up large sums and waiting an
eternity.

Andy

Andy, where are you located? I'll be in London soon, would a visit
be easy and possible? I'm a retired EE and not looking for work,
slug lazy and proud of it -- but I'd like to see your plating op
because I'm interested in plating. I do a bit of that, just small
stuff in my garage, no chrome. I'll be in London to visit with
new granddaughter -- but I can only take so much baby stuff before I
start getting antsy. I'd love an excuse to hop on the tube or a
train for a day if it's not too heroic an adventure.
 
J

John Larkin

Jan 1, 1970
0
Right! That's why I recommended using 10 of them.

I stipulated that heatsink-related issues were "given" per OP's post,
and that cost of labor was not included. I think that's the OP's
intent: to use available in-house labor to reduce cashflow cost.

Fooey! Please say more about how SCR's would be safer -- or simpler
for that matter. I don't think so. Please show sources and prices
for the cheap trigger boards and packaged SCR bridges that you
mention -- and how these might be assembled to meet the OP's request.

Even with 3 phase excitation there's no way they'll strip ripple like
a series-pass bank of MOSFET's would. That flat isn't on with SCR's.

This is not a "serious project" if the OP can do the watercooled
heatsink he said he could. Please show how doing it with SCR's
would be simpler, even with significantly inferior performance.

You want a design? I'll need a purchase order. If you can build these
for $500 each, and the market price is 3x as much, you should go into
the business.


John
 
C

Chris Jones

Jan 1, 1970
0
Andy said:
Hi all,

I'm looking at building a Voltage Controlled Current Source; approx 15V
output, with up to 70A available - I need to be able to control the
current.

I've found this schematic (http://www.neillans.co.uk/VCCS1.pdf), and if
I were to uprate all the components (e.g. from 1/4W resistors to 1W or
higher), and replaced the IRFZ48Vs with the IRFZ48Ns which have a
higher current load, would it work?
I tried to build + simulate this circuit in EWB, but it didn't work out
- but that could be down to my VHDL :)

I've been working with electronics etc for years, but never ventured
far from digital solutions, although I have knocked up power supplies
in the past, they have never been VCCS.

Please Help :)

Andy

I've made a couple of VCCS type plating power supplies capable of reverse
pulse waveforms (or other waveforms if you wanted...), but none as big as
what you're suggesting. The first one I did used a TDA2030 audio op-amp
(very cheap opamp, puts out at least an amp but has large DC offset, and
not unity gain stable). The circuit ran off split supplies, probably about
+/-10V. I connected the supply pins of the op-amp to the bases of 2N3055
and 2N2955 transistors to boost the output current, so when the op-amp
would start to struggle with the output current, it gets a bit of 'help'
from the power transistor. I think it would do about 10 Amps comfortably
but I can't remember and didn't need to push it too far anyway because the
object being plated was small. (The emitter of the PNP 2N2955 goes to the
positive supply, the collector goes to the op-amp output, the positive
supply pin of the TDA2030 goes to the base of the 2N2955, and there is a
resistor maybe 10 Ohms from the base to emitter. Same for the NPN 2N3055,
but the emitter goes to the negative rail and the base goes to the negative
supply pin of the TDA2030. The output of my boosted power op-amp went
(through a small resistor or inductor to help stability I think...) to one
electrode of the plating tank, and the other electrode of the plating tank
went through a current sensing resistor to the common of the power supply.
I say common rather than ground, because I think I actually floated the
power supply itself to allow one of the electrodes to be grounded if so
desired. Of course the current sense resistor develops a voltage which is
fed back to the inverting input of the TDA2030, and the non-inverting input
is driven with the waveform which you want the current to follow, that
waveform being with respect to the common of the power supply, (not
necessarily ground). I think I used a 555 timer and a 4066 chip and
several pots, to make the reverse pulse waveform. I think I needed some
fancy things like Zobel networks to make it all stable, most of which I
copied out of the TDA2030 datasheet (which contains only audio circuits),
and tweaked by trial and error, with various test loads and looking for
ringing on a scope.

By the way, the TDA2030A and 2040 are probably better, I think one of them
includes protection diodes to the supplies which are absent from the 2030,
and the current rating might be better.

The second plating supply was much fancier, it had 16 channels to drive 16
independent plating outputs, and the current sources were proper ones which
could drive a real ground referenced load - I used a current sensing
resistor in series with the output pin of the power op-amp. I think each
channel would drive 1Amp and it was all software controlled using DACs and
a PIC microcontroller connected to a PC through a serial cable. If you're
really interested I could try to find the old schematics, but it's in
protel format so it'd take me a while to fix up a PC to convert it to
anything else.

Chris
 
A

Andy Neillans

Jan 1, 1970
0
First off, just want to thank everyone for their input; been unwell, so
haven't been online a lot recently (hence my dissappearance).


Chris;

Many thanks for sharing your experiences :)
The second plating supply was much fancier, it had 16 channels to drive 16
independent plating outputs, and the current sources were proper ones which
could drive a real ground referenced load - I used a current sensing
resistor in series with the output pin of the power op-amp. I think each
channel would drive 1Amp and it was all software controlled using DACs and
a PIC microcontroller connected to a PC through a serial cable. If you're
really interested I could try to find the old schematics, but it's in
protel format so it'd take me a while to fix up a PC to convert it to
anything else.

If you would be willing to share, I'd certainly like to take a look! I
work a lot with the Atmel AVR Risc uC's at work, and have been drafting
including one in the PSU - specifically to digitise the regulation and
allow monitoring and control via our network (already have TCP/IP
Stacks for the AVR, as well as code that makes use of the built in ADC
- both from existing projects).


Dan;
Based a little bit further up the country these days (although until 8
- 9 months ago, I lived just south of London!). We are in the Scottish
Borders, about an hour south of Edinburgh. If you want to come up, let
me know - am sure I could arrange for a visit! You never know, I might
even have the new supply up and running..

Andy
 
Top