Maker Pro
Maker Pro

circuit for pulse generation

reza

Oct 3, 2013
7
Joined
Oct 3, 2013
Messages
7
Hi
I have pressing need for the following pulse:
The Square Wave specifications are as follows:
The pulse consists of: ON(Positive voltage)- OFF- ON(Negative voltage)- OFF .........
T(ON)= T(OFF)
X1= 0.25 S – 8 S
X2= Number of cycles = 2- 4- 6- 8- 10
X3= output voltage
In this circuit output voltage and output current should be variable and X1, X2 and start trigger should be obtained with USB port (LABVIEW software) or keyboard or other
Please help me with schematic; PCB; program; about this circuit;
Pulse is shown in the following image.
I wish you all the best
Thanks;
 

Attachments

  • SHEMATIC.jpg
    SHEMATIC.jpg
    17.6 KB · Views: 143

(*steve*)

¡sǝpodᴉʇuɐ ǝɥʇ ɹɐǝɥd
Moderator
Jan 21, 2010
25,510
Joined
Jan 21, 2010
Messages
25,510
Please help me with schematic; PCB; program; about this circuit;

Sure, can we get you a coffee while you wait? Maybe something stronger from our well-equipped bar? I think Fifi is in today, she can give you a delightful massage to make you more relaxed...

Now you're in the mood, if you want this thread to have a happy ending, just remember that we're here to help you out of the goodness of our hearts. We're NOT here to do your bidding.

You have an impressive set of requirements, but very few hard specification.

Firstly, there are multiple ways to produce that output. You could use an H bridge, or the output of an amplifier.

But what voltages, what range of current limits? what happens at zero volts output (is the output shorted to ground, or open. If the former, does the current limit still apply?

Is slew rate important?

What will the USB interface do?

This would be a large project, and I'd be happy to start with telling you about the options as to how you might go about generating the output waveform.

So I'm afraid that if you want that happy ending, you're going to have to skip the trip to the bar and help us out.
 

reza

Oct 3, 2013
7
Joined
Oct 3, 2013
Messages
7
First,Thank you for your attention
output voltage can be 0 - 15v and current is 0- 2 A or Any amount that you can design. Output waveform should be Similar to the proposed.
X1 and X2 and X3 and start trigger can be Regulated with use keyboard or USB interface (by labview software).
If the project is large, Please send for me the circuit design with generate the square wave with this waveform without attention to other cases,
Thank you very much
 

(*steve*)

¡sǝpodᴉʇuɐ ǝɥʇ ɹɐǝɥd
Moderator
Jan 21, 2010
25,510
Joined
Jan 21, 2010
Messages
25,510
I would suggest you look at an H-Bridge circuit. That can be easily configured to give the waveform you desire.

The voltage and current limiting would need to be looked at separately.
 

reza

Oct 3, 2013
7
Joined
Oct 3, 2013
Messages
7
Thanks
please, help me in Additional Details about H-Bridge circuits for this waveform and shematic for it.
can you tell me about voltage and current limiting circuit.
 

reza

Oct 3, 2013
7
Joined
Oct 3, 2013
Messages
7
hi
please help me for voltage and current limiting circuit?
 

BobK

Jan 5, 2010
7,682
Joined
Jan 5, 2010
Messages
7,682
Reza,

Who is asking you to do this project that you have, apparently, no skills to perform?

Bob
 

gorgon

Jun 6, 2011
603
Joined
Jun 6, 2011
Messages
603
Reza,
Could this be an Electro-Osmotic pulse generator?
 

reza

Oct 3, 2013
7
Joined
Oct 3, 2013
Messages
7
hi gorgon
I have need to this circuit for a student project.
If it is possible please help me.
Thank you so much
 

BobK

Jan 5, 2010
7,682
Joined
Jan 5, 2010
Messages
7,682
Do you also copy all of your term papers from the internet?

Bob
 

reza

Oct 3, 2013
7
Joined
Oct 3, 2013
Messages
7
I do not understand what you mean
I just wanted to help me
 

BobK

Jan 5, 2010
7,682
Joined
Jan 5, 2010
Messages
7,682
No, you want us to do your project for you.

If what you want is help, how about telling us what you have done so far and what problems you are having with your design.

Bob
 
Top