Maker Pro
Maker Pro

getting sine wave on the oscilloscope?

S

Sam Kaan

Jan 1, 1970
0
I want to see some stuffs on my oscilloscope to get the feel for it.

I have lying around the box an AC adapter, transformer or whatever you
call it.

This AC adapter plugs into the wall outlet of 120V 60Hz. And out of
the
other ends comes 16V AC (that's right AC not DC). So I figure if its
AC
then it should be oscillating and I can see it on the scope.

Now let me say that I am quite inexperience with an oscilloscope.

Ok. To display this sine wave on my scope, I take it all I have to do
is
take the two ends from the AC Adapter output and put it as input into
the scope
right? ie. feed it as input into the probe? correct? Set the volt
division
to say 0.2V, then flip the time base division until I see a sine wave,
I know you can probably calculate but I am not sure if the output of
16VAC is at 60Hz or not. Sounds about right?

By the way, what are special about the probes, does it do anything to
the signal of 16VAC before its fed into the scope (plugin 7A13 of my
Tek7904).
Does 16VAC amplitude get fed in or does the probe de-magnify it into
something much smaller (to protect the scope perhaps).

Any taker?
 
R

Robert Baer

Jan 1, 1970
0
Sam said:
I want to see some stuffs on my oscilloscope to get the feel for it.

I have lying around the box an AC adapter, transformer or whatever you
call it.

This AC adapter plugs into the wall outlet of 120V 60Hz. And out of
the
other ends comes 16V AC (that's right AC not DC). So I figure if its
AC
then it should be oscillating and I can see it on the scope.

Now let me say that I am quite inexperience with an oscilloscope.

Ok. To display this sine wave on my scope, I take it all I have to do
is
take the two ends from the AC Adapter output and put it as input into
the scope
right? ie. feed it as input into the probe? correct? Set the volt
division
to say 0.2V, then flip the time base division until I see a sine wave,
I know you can probably calculate but I am not sure if the output of
16VAC is at 60Hz or not. Sounds about right?

By the way, what are special about the probes, does it do anything to
the signal of 16VAC before its fed into the scope (plugin 7A13 of my
Tek7904).
Does 16VAC amplitude get fed in or does the probe de-magnify it into
something much smaller (to protect the scope perhaps).

Any taker?

While you could blindly go ahead with this project, it would be far
wiser to learn about electronics and electronic test equipment FIRST.

You would not futz around with nitoglycerine, gunpowder, and such
other compounds before learning about explosives and the proper handling
thereof.
Or "experiment" with a strange four-wheeled device that others call a
"car" if you knew absolutely nothing about them.
Or take a clear, pretty rock that you have heard that diamond cutters
make valuable cuts therefrom and chip away until the nice looking gem
"hiding inside" was exposed?
Yes, a number of ignorant people have done such things because they
knew just enough to be (literally) dangerous and were too self-centered,
boastful, and unwise to *know* that they in fact did NOT know spit and
leave things alone.

I have met a number of people that had only 8th grade or less of
education, but were long on wisdom.
And others with college degrees that were (to be blunt) STUPID.
And i would implicitly trust the first group and use armed guards to
protect things from the second group.
 
J

JeffM

Jan 1, 1970
0
I want to see some stuffs on my oscilloscope to get the feel for it.
While you could blindly go ahead with this project, it would be far
wiser to learn about electronics and electronic test equipment FIRST.

Robert Baer

RB's right.
1st, break out the operator's manual that came with the instrument.
Once you understand Vertical scaling, Timebase scaling,
and Triggering (especially auto-triggering)
then (and only then) do you start touching the hardware.
 
C

ChronoFish

Jan 1, 1970
0
Robert Baer said:
While you could blindly go ahead with this project, it would be far
wiser to learn about electronics and electronic test equipment FIRST.

You would not futz around with nitoglycerine, gunpowder, and such
other compounds before learning about explosives and the proper handling
thereof.
Or "experiment" with a strange four-wheeled device that others call a

blah blah blah
I have met a number of people that had only 8th grade or less of
education, but were long on wisdom.
And others with college degrees that were (to be blunt) STUPID.
And i would implicitly trust the first group and use armed guards to
protect things from the second group.

Your two comments here, in my uneducated opinion, don't mesh.

The "8th grade educated" is more likely to have real hands on experience, learned from trial and error, learned from working with
mentors, and in general learned from "doing".

The "College educated" is much more likely to be "book smart" - having learned all they could by studying and reading - but not
having the experience to know how things "really work".

It appears your comments are saying "be book smart - but I wouldn't trust you if you were."

Having said that, despite my college degree, I think it's perfectly acceptable to start doing what comes natural - experiment and
ask questions.

Personally I wouldn't be able to sit through an oscilloscope manual or any other book that makes me yawn in 30 seconds. This is how
my father presented electronics to me when I was 13. He some how thought that me knowing which soldering compound to choose was
more important than letting me play with a soldering iron. I didn't touch an electronics book again until I graduated from college
when I started "doing" and experimenting with a PIC. My father has a wealth of information when it comes to electronics - but has
done virtually nothing with it. Meanwhile I don't know shit but I've somehow managed to have a PCB created - and then populated by
another company - and it all works as planned.

In my opinion its the book readers who are "Holier than thou" and who believe there is only one way learn about electronics - and
that is to memorize "Horrowitz and Hill" before you dare step into an electronics lab.

Bah!

It took me a grand total of 15 minutes sitting down with my father-in-law, (another hands first type of guy) to finally "get" how to
use an oscilloscope. The book route I never would have "gotten" because I would have lost interest.


CF
 
Top