Maker Pro
Maker Pro

[HELP]Audio power amplifier analysis

foolah44

Nov 15, 2012
1
Joined
Nov 15, 2012
Messages
1
Hi,
I have a pre-designed audio power amplifier to analyse and test. The circuit is attached.

I have got several values but during test some of them were not quite right.

My results
__________

differential (input) stage of about (-) 65.2 - that is for Q1
second stage gain of about 1224 - that is for Q4
feedback ratio, about 1/25 i.i 0.04
Overall gain of about 26

Input impedance of about 4.4KΩ
Output impedance of less that 1Ω

Low frequency limit of about 32Hz due to C2
High frequency limit of about 133kHz due to C3


at the output stage, we assume a load of 8Ω
Maximum operational output voltage was about 3V peak (positive)

which gave me an operational power delivered of about 0.56W

Power supply is about 1W
so effieciency gives me about 56%

The maximum power dissipated at each output transistor was about 0.51W
So heatsink not really needed.


TESTING
________
When testing my amplifier, The low and high frequencies limits were not right. I got about 25Hz and 4MHz for low and high frequency limits.

Can you please help me check my results. Especially for high and low frequency limits, and also power analysis?
 

Attachments

  • circuit for site.jpg
    circuit for site.jpg
    62.6 KB · Views: 259

(*steve*)

¡sǝpodᴉʇuɐ ǝɥʇ ɹɐǝɥd
Moderator
Jan 21, 2010
25,510
Joined
Jan 21, 2010
Messages
25,510
C3 may act to reduce the gain of the amplifier, but that capacitor is within the feedback loop.

I think you'll find that the open loop gain may roll off as you expect, however the closed loop gain will hold up much longer (essentially until the closed loop gain approximates the open loop gain).

The low frequency rolloff is done in the feedback loop itself, and I suspect the differences may be due to component tolerances or a slight miscalculation (I have neither done the maths nor built your circuit)
 

FutureFuzz 26

Nov 15, 2012
12
Joined
Nov 15, 2012
Messages
12
Hi,
I have a pre-designed audio power amplifier to analyse and test. The circuit is attached.

I have got several values but during test some of them were not quite right.

My results
__________

differential (input) stage of about (-) 65.2 - that is for Q1
second stage gain of about 1224 - that is for Q4
feedback ratio, about 1/25 i.i 0.04
Overall gain of about 26

Input impedance of about 4.4KΩ
Output impedance of less that 1Ω

Low frequency limit of about 32Hz due to C2
High frequency limit of about 133kHz due to C3


at the output stage, we assume a load of 8Ω
Maximum operational output voltage was about 3V peak (positive)

which gave me an operational power delivered of about 0.56W

Power supply is about 1W
so effieciency gives me about 56%

The maximum power dissipated at each output transistor was about 0.51W
So heatsink not really needed.


TESTING
________
When testing my amplifier, The low and high frequencies limits were not right. I got about 25Hz and 4MHz for low and high frequency limits.

Can you please help me check my results. Especially for high and low frequency limits, and also power analysis?

im not trying to step on toes here, but whats the point of having frequency respnse that high? most music takes place from between 25-10khz

and why limit your self to 8ohm on the output, 4,2,1 and even .5 is pretty common in the audio indistry these days
 
Top