Maker Pro
Maker Pro

Monostable multivibrator

Bekzat

Feb 20, 2017
4
Joined
Feb 20, 2017
Messages
4
Hello, working on project where I need a monostable multivibrator.
The question is: How can I make two unstable and one stable states, like +vcc and -vcc are unstable and 0v is the stable one. Example: if Positive triggers it goes +vcc for a wile and comes back to a 0 volts, else negative triggers output goes -vcc for some time and comes back to 0 volts
 

AnalogKid

Jun 10, 2015
2,698
Joined
Jun 10, 2015
Messages
2,698
That is not a normal monostable, but a standard chip or circuit can do that with some extra parts. You don't say if the two pulse periods need to be exactly the same, or only within 10%. Off the top, one approach:
Input goes directly to one monostable with negative input protection, and to a bipolar inverter that drives a second monostable. Output of the first pulser is the positive output pulse. Output of the second pulser goes to a bipolar inverter to make the negative output pulse. Sum the two outputs into a common bipolar output driver.

1. Are the output pulses longer than the input pulses. In other words, does the input trigger signal return to 0 before or after the end of the corresponding output pulse?

2. What is the load? How much current does the output need to deliver?

3. What is the speed? What are the maximum rise and fall times of the output pulses?

4. What are the values of Vcc (the positive supply voltage) and Vee (the negative supply voltage)?

5. AND - what are the output pulse widths and tolerance?

ak
 

Bekzat

Feb 20, 2017
4
Joined
Feb 20, 2017
Messages
4
That is not a normal monostable, but a standard chip or circuit can do that with some extra parts. You don't say if the two pulse periods need to be exactly the same, or only within 10%. Off the top, one approach:
Input goes directly to one monostable with negative input protection, and to a bipolar inverter that drives a second monostable. Output of the first pulser is the positive output pulse. Output of the second pulser goes to a bipolar inverter to make the negative output pulse. Sum the two outputs into a common bipolar output driver.

1. Are the output pulses longer than the input pulses. In other words, does the input trigger signal return to 0 before or after the end of the corresponding output pulse?

2. What is the load? How much current does the output need to deliver?

3. What is the speed? What are the maximum rise and fall times of the output pulses?

4. What are the values of Vcc (the positive supply voltage) and Vee (the negative supply voltage)?

5. AND - what are the output pulse widths and tolerance?

ak

1. Are the output pulses longer than the input pulses. In other words, does the input trigger signal return to 0 before or after the end of the corresponding output pulse?

Output pulses are longer than input

2. What is the load? How much current does the output need to deliver?

The load is DC gear motor 6vdc, the current is around 0.11A
-Vee is for the ccw, +vcc for cw

3. What is the speed? What are the maximum rise and fall times of the output pulses?

I need output signal time around 5s

4. What are the values of Vcc (the positive supply voltage) and Vee (the negative supply voltage)?

+9v and -9v


5. AND - what are the output pulse widths and tolerance?

Depends on timing, say it is 5 seconds


Thanks
If you can help me with this, would be great!!!
 
Last edited by a moderator:

AnalogKid

Jun 10, 2015
2,698
Joined
Jun 10, 2015
Messages
2,698
6.
a) All solid state solution
b) All relays and diodes
c) Solid state control of relay output stage?

ak
 

BobK

Jan 5, 2010
7,682
Joined
Jan 5, 2010
Messages
7,682
d. Microcontroller and 3 MOSFETs (half bridge and level translator)

Bob
 

AnalogKid

Jun 10, 2015
2,698
Joined
Jun 10, 2015
Messages
2,698
OK, let's ask:

Bekzat - do you own, have access to, or have ever used a microcontroller software development system and device programmer?

Bob - won't you need two level translators?

ak
 

Bekzat

Feb 20, 2017
4
Joined
Feb 20, 2017
Messages
4
OK, let's ask:

Bekzat - do you own, have access to, or have ever used a microcontroller software development system and device programmer?

Bob - won't you need two level translators?

ak

Yea I have an access, but it is analogue project. Requirements are pure electronics without implementation of a microcontrollers
 

BobK

Jan 5, 2010
7,682
Joined
Jan 5, 2010
Messages
7,682
OK, let's ask:

Bekzat - do you own, have access to, or have ever used a microcontroller software development system and device programmer?

Bob - won't you need two level translators?

ak
With the supply at 9V, yes, you would need two level translators. I was thinking 5V supplies.

Bob
 

AnalogKid

Jun 10, 2015
2,698
Joined
Jun 10, 2015
Messages
2,698
Are open collector output ok, or do you need the output to be driven back to 0 V after a pulse?

ak
 

AnalogKid

Jun 10, 2015
2,698
Joined
Jun 10, 2015
Messages
2,698
But - the motor also will not run if the output goes to a high impedance, such as an open collector stage that is turned off.

What is it you want to achieve? How many motors are there, are they uni- or bi-directional? Etc?

If the idea is that there is one motor that runs in one direction with a positive input pulse and in the other direction with a negative input pulse, it's kinda important to know that because it changes the output stages. Also, SPDT relays are perfect for that kind of operation, but we don't know if relays are acceptable. See post #4.

ak
 
Top