Maker Pro
Maker Pro

opamp somehow exceeds open loop gain!

A

Asa Cannell

Jan 1, 1970
0
I have an opamp (OPA348 to be exact) in a non inverting configuration.
Take a standard noninverting configuration (two resistors in series
from output to ground, resitor junction connected to inverting input),
but instead of connecting the resistor network to ground, connect it
to one side of a capacitor, and the other side of the capacitor to
ground. Now we frequency variable gain, (high pass).

In the simulator, if I change the large resistor to 1000k and the
small resistor to 3.16k, and the capacitor to .001125uF, I am getting
a gain of 316 at 12KHz. This exceeds the opamps open loop gain
specified in the datasheet, which is well under 40db (100) at 12KHz.
I have a 100k resistor on the opamps output as a load, per the
datasheet.

How is this possible? Is the opamps phase shifts somehow acting as an
inductor, and along with the capacitor, somehow a series resonant LC
circuit is formed and I am getting voltage gain? (please post
responses in the forum)

Asa
 
S

Soeren

Jan 1, 1970
0
Hi Asa,

In the simulator, [...] This exceeds the opamps open loop gain
specified in the datasheet [...]
How is this possible? [...]

Simulators are nice toys, but they cannot be better than the models used
(and the programming).

If you "simulate" with your brain and some real life components...
WYSIWYG.
 
R

Roy McCammon

Jan 1, 1970
0
Asa said:
I have an opamp (OPA348 to be exact) in a non inverting configuration.
Take a standard noninverting configuration (two resistors in series
from output to ground, resitor junction connected to inverting input),
but instead of connecting the resistor network to ground, connect it
to one side of a capacitor, and the other side of the capacitor to
ground. Now we frequency variable gain, (high pass).

In the simulator, if I change the large resistor to 1000k and the
small resistor to 3.16k, and the capacitor to .001125uF, I am getting
a gain of 316 at 12KHz. This exceeds the opamps open loop gain
specified in the datasheet, which is well under 40db (100) at 12KHz.
I have a 100k resistor on the opamps output as a load, per the
datasheet.

How is this possible? Is the opamps phase shifts somehow acting as an
inductor, and along with the capacitor, somehow a series resonant LC
circuit is formed and I am getting voltage gain? (please post
responses in the forum)

Asa

you are probably getting enough phase shift ( almost 90 for
the op amp and almost 90 for your feedback) to have almost
positive feed back. Its also called regenerative gain.
Bottom line yes you can get extra gain that way
but the actual gain is very sensitive. In effect
you have an almost oscillator.
 
F

Fred Stevens

Jan 1, 1970
0
I have an opamp (OPA348 to be exact) in a non inverting configuration.
Take a standard noninverting configuration (two resistors in series
from output to ground, resitor junction connected to inverting input),
but instead of connecting the resistor network to ground, connect it
to one side of a capacitor, and the other side of the capacitor to
ground. Now we frequency variable gain, (high pass).

In the simulator, if I change the large resistor to 1000k and the
small resistor to 3.16k, and the capacitor to .001125uF, I am getting
a gain of 316 at 12KHz. This exceeds the opamps open loop gain
specified in the datasheet, which is well under 40db (100) at 12KHz.
I have a 100k resistor on the opamps output as a load, per the
datasheet.

How is this possible? Is the opamps phase shifts somehow acting as an
inductor, and along with the capacitor, somehow a series resonant LC
circuit is formed and I am getting voltage gain? (please post
responses in the forum)

Asa


The closed loop gain equation Av = 1 + Zf/Zg (Zg the impedance to
ground) is accurate under the assumption that the open loop op amp
gain is infinity which is clerly not the case with your circuit!
Obviously the simulator you are using is making certain "assumptions"

Fred.
 
A

Asa Cannell

Jan 1, 1970
0
Roy McCammon said:
you are probably getting enough phase shift ( almost 90 for
the op amp and almost 90 for your feedback) to have almost
positive feed back. Its also called regenerative gain.
Bottom line yes you can get extra gain that way
but the actual gain is very sensitive. In effect
you have an almost oscillator.


By extra gain do you mean gain above open loop gain? (seemingly
violating the datasheet spec). I notice that the inverting terminal is
approximately equal to the noninverting terminal over most of the
freq. band (as expected), but where I have the "extra gain" peak, it
also peaks, and is no longer equal to the noninverting input at that
frequency.

Asa
 
K

Kevin Aylward

Jan 1, 1970
0
Fred said:
[email protected] (Asa Cannell) wrote in message



The closed loop gain equation Av = 1 + Zf/Zg (Zg the impedance to
ground) is accurate under the assumption that the open loop op amp
gain is infinity which is clerly not the case with your circuit!
Obviously the simulator you are using is making certain "assumptions"

Well, the "simulator" doesn't make those kinds of assumptions. It does
what it is told to do, usually. It solves equations very accurately. The
*model* may well have approximations and assumptions that result in
these accurate solutions but have incorrect results.

Kevin Aylward
[email protected]
http://www.anasoft.co.uk
SuperSpice, a very affordable Mixed-Mode
Windows Simulator with Schematic Capture,
Waveform Display, FFT's and Filter Design.
 
F

Fred Stevens

Jan 1, 1970
0
Kevin Aylward said:
Well, the "simulator" doesn't make those kinds of assumptions. It does
what it is told to do, usually. It solves equations very accurately. The
*model* may well have approximations and assumptions that result in
these accurate solutions but have incorrect results.

What I meant is that the simulator uses a model in which certain
assumptions (and approximations) are made.

Fred.
 
R

Roy McCammon

Jan 1, 1970
0
Asa said:
By extra gain do you mean gain above open loop gain?
yes


(seemingly
violating the datasheet spec). I notice that the inverting terminal is
approximately equal to the noninverting terminal over most of the
freq. band (as expected), but where I have the "extra gain" peak, it
also peaks, and is no longer equal to the noninverting input at that
frequency.

so look at the ratio of the output to difference between
those two pins to see if the gain of the opamp is
what you expect.
 
Top