Maker Pro
Maker Pro

Sansui 9090

G

GD

Jan 1, 1970
0
Hello All;
I have a Sansui 9090 since I bought it new. Other then a few small
problems with it over the 30+ years I have own and operated it has been a
great receiver. Reciently I was playing tunes, when suddenly the receiver
quit playing. It was still powered up, and when I checked it out the switch
warning was, and is flashing red constantly, when it should change to green
after first turning on. It is an overload protection switch, and it won't
change to it's normal green when all systems are go color. In the past if I
were to drive it to hard, it would do the same, but after adjusting volume
and bass down, it would be fine again.now it stays in this flashing red
mode, and will not clear and turn solid green as it should.
Has any one any ideas on this one. Thank You
 
B

Bob

Jan 1, 1970
0
GD said:
Hello All;
I have a Sansui 9090 since I bought it new. Other then a few small
problems with it over the 30+ years I have own and operated it has been a
great receiver. Reciently I was playing tunes, when suddenly the receiver
quit playing. It was still powered up, and when I checked it out the
switch warning was, and is flashing red constantly, when it should change
to green after first turning on. It is an overload protection switch, and
it won't change to it's normal green when all systems are go color. In the
past if I were to drive it to hard, it would do the same, but after
adjusting volume and bass down, it would be fine again.now it stays in
this flashing red mode, and will not clear and turn solid green as it
should.
Has any one any ideas on this one. Thank You

Yes. The problem is that you don't know when to use "it's" and when to use
"its".

Bob
 
J

John E.

Jan 1, 1970
0
I think you want to post this to scile.ectronics.repair.

Good luck,
 
J

Jamie

Jan 1, 1970
0
GD said:
Hello All;
I have a Sansui 9090 since I bought it new. Other then a few small
problems with it over the 30+ years I have own and operated it has been a
great receiver. Reciently I was playing tunes, when suddenly the receiver
quit playing. It was still powered up, and when I checked it out the switch
warning was, and is flashing red constantly, when it should change to green
after first turning on. It is an overload protection switch, and it won't
change to it's normal green when all systems are go color. In the past if I
were to drive it to hard, it would do the same, but after adjusting volume
and bass down, it would be fine again.now it stays in this flashing red
mode, and will not clear and turn solid green as it should.
Has any one any ideas on this one. Thank You
You most likely have bad caps and maybe an output transistor, why not
post to the repair group.
 
M

Meat Plow

Jan 1, 1970
0
Hello All;
I have a Sansui 9090 since I bought it new. Other then a few small
problems with it over the 30+ years I have own and operated it has been a
great receiver. Reciently I was playing tunes, when suddenly the receiver
quit playing. It was still powered up, and when I checked it out the switch
warning was, and is flashing red constantly, when it should change to green
after first turning on. It is an overload protection switch, and it won't
change to it's normal green when all systems are go color. In the past if I
were to drive it to hard, it would do the same, but after adjusting volume
and bass down, it would be fine again.now it stays in this flashing red
mode, and will not clear and turn solid green as it should.
Has any one any ideas on this one. Thank You

My idea would be to have it repaired.
 
Top