Voltage Divider

M

Marco T.

Jan 1, 1970
0
Hallo,
I have thought to use a voltage divider to have an input voltage range
of -10v to +10v and and output of -2,5v to +2,5v.

Following the schema: Input -> R1 ->output
|
R2
|
Ground

I can choose between:
R1 R2
7500 1500
10000 2000
12000 2400

What is the difference in choosing R1 R2 couples?

Many Thanks
Marco

M

Marco T.

Jan 1, 1970
0
Marco T. said:
Hallo,
I have thought to use a voltage divider to have an input voltage range
of -10v to +10v and and output of -2,5v to +2,5v.

Following the schema: Input -> R1 ->output
|
R2
|
Ground

I can choose between:
R1 R2
7500 1500
10000 2000
12000 2400

What is the difference in choosing R1 R2 couples?

Many Thanks
Marco

What is the difference between using Ground or a reference voltage?

Thanks Again
Marco

J

John Larkin

Jan 1, 1970
0
Hallo,
I have thought to use a voltage divider to have an input voltage range
of -10v to +10v and and output of -2,5v to +2,5v.

Following the schema: Input -> R1 ->output
|
R2
|
Ground

I can choose between:
R1 R2
7500 1500
10000 2000
12000 2400

What is the difference in choosing R1 R2 couples?

Many Thanks
Marco

No difference; they're all wrong.

John

M

Jan 1, 1970
0
G

Greg Neill

Jan 1, 1970
0
Marco T. said:

Show your math for determining the resistance ratios.

M

Marco T.

Jan 1, 1970
0
Greg Neill said:
Show your math for determining the resistance ratios.

I have used a script into TI site.

http://www-k.ext.ti.com/srvs/cgi-bin/webcgi.exe?Company={5761bcd8-11f5-4e08-84e0-8167176a4ed9},kb=analog,case=obj(32620),new

I have re-used the script and it has showed different values.
R1 R2
12000 3000
30000 7500
Maybe I typed a wrong value.

Into the script there is the possibility to choose resistor scale 10, 100,
1000, ecc.

What is the difference, in this case between the 2 possibilities?

Many Thanks
Marco

M

Marco T.

Jan 1, 1970
0
Spehro Pefhany said:
They're still wrong. There's not much data input validation on that
script. You will need to conform to American practice and use "."
rather than "," as the radix point. One exact possibility would be 39K
& 13K

example I gave above).

Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
[email protected] Info for manufacturers:
http://www.trexon.com
http://www.speff.com

Input stage of voltage divider should be a strain gauge with signal
conditioning to obtain 0 10v in single ended, or -10 +10 volt in
differential.

Instead the output should be a voltage follower.

Which could be a good resistor configuration?

Many Thanks
Marco

S

Spehro Pefhany

Jan 1, 1970
0
I have re-used the script and it has showed different values.
R1 R2
12000 3000
30000 7500
Maybe I typed a wrong value.

Into the script there is the possibility to choose resistor scale 10, 100,
1000, ecc.

They're still wrong. There's not much data input validation on that
script. You will need to conform to American practice and use "."
rather than "," as the radix point. One exact possibility would be 39K
& 13K
What is the difference, in this case between the 2 possibilities?

Many Thanks
Marco

example I gave above).

Best regards,
Spehro Pefhany

G

Greg Neill

Jan 1, 1970
0
Marco T. said:
Input stage of voltage divider should be a strain gauge with signal
conditioning to obtain 0 10v in single ended, or -10 +10 volt in
differential.

Instead the output should be a voltage follower.

Which could be a good resistor configuration?

Many Thanks
Marco

Do you have any additional specifications on the
strain gauge such as its output impedance or
allowable current range?

You want to choose resistor values such that
they won't represent too low an impedance
compared to that of the gauge in order to

M

mc

Jan 1, 1970
0
Marco T. said:
Hallo,
I have thought to use a voltage divider to have an input voltage range
of -10v to +10v and and output of -2,5v to +2,5v.

Following the schema: Input -> R1 ->output
|
R2
|
Ground

I can choose between:
R1 R2
7500 1500
10000 2000
12000 2400

I think you want the output to be 1/4 of the input, not 1/6. So: 7500:2500,
12000:4000, etc. (none of which are standard resistor values).
What is the difference in choosing R1 R2 couples?

The amount of current that will flow into the input and the amount of
additional voltage drop caused by current flowing out the output.

What is connected to the input and to the output?

J

John Larkin

Jan 1, 1970
0

You want the output to be 1/4 of the input.

So imagine a string of four equal resistors, +10 volts on one end and
ground on the other. Call the voltages at the connections A B and C

A B C
+10------r-------r-------r-------r------gnd

By symmetry, B os halfway from +10 to gnd, so Vb must be +5 volts.

Again, by symmetry, Vc must be 2.5 volts, which is what you wanted.

You can combine the left three resistors into 3R.

So R1 must be 3x R2.

John

J

John Perry

Jan 1, 1970
0
Greg said:
Do you have any additional specifications on the
strain gauge such as its output impedance or
allowable current range?

The strain gauge specs don't matter; he has a signal conditioner. What
he needs is the output current limit of the signal conditioner, which
will be more than adequate for any of the total resistances that anyone
has mentioned, including Spehro's correct one.

Since he intends to put a voltage follower on it, the same applies to
the output. Any total resistance from ~2K to ~500K will be fine for
just about any combination of signal conditioner and voltage follower
I've ever heard of. Choose something convenient in the middle. Just
keep in mind John's demonstration of 3R -- R, and make sure 4R is great
have specs for.

John Perry

Replies
16
Views
1K
Replies
4
Views
1K
Replies
18
Views
4K
Replies
4
Views
2K
Replies
40
Views
4K