Maker Pro
Maker Pro

Wiring LEDs together

A

alokw

Jan 1, 1970
0
Hi all,

I have a quick question that should be simple to answer.
I have 54 LEDs that require 3.4 V DC with a maximum of 30 mA that need
to be wired together.
I have 9V batteries to power them.

I did the calculations and ended up wiring them in series of 2 LEDS
with an 82 ohm resistor for each pair and hooked up the end to a
single 9V battery. With the 27 pairs, it was suppsed to draw 810 mA.

When I switched it on, everything was dim. I didn't think about how
many mA the battery could provide.

My alternative idea is to wire 2 9V batteries together and wire 55
LEDs in series of 5 LEDs with a 39 ohm resistor with each series. This
*should* draw 330 mA. Right?

I think this will work, but want to verify it with you people that
know what you're doing before I buy more 9V batteries and new
resistors. I just want all the LEDs to be as bright as possible.

Thanks for your help!
 
M

martin griffith

Jan 1, 1970
0
Hi all,

I have a quick question that should be simple to answer.
I have 54 LEDs that require 3.4 V DC with a maximum of 30 mA that need
to be wired together.
I have 9V batteries to power them.

I did the calculations and ended up wiring them in series of 2 LEDS
with an 82 ohm resistor for each pair and hooked up the end to a
single 9V battery. With the 27 pairs, it was suppsed to draw 810 mA.

When I switched it on, everything was dim. I didn't think about how
many mA the battery could provide.

My alternative idea is to wire 2 9V batteries together and wire 55
LEDs in series of 5 LEDs with a 39 ohm resistor with each series. This
*should* draw 330 mA. Right?

I think this will work, but want to verify it with you people that
know what you're doing before I buy more 9V batteries and new
resistors. I just want all the LEDs to be as bright as possible.

Thanks for your help!
forget about PP3 9V batteries, they are unsuitable.

From the Duracell MN1604 datasheet:

Rated capacity 580mAH.
At just 25mA load the volts drop to about 7.5V in ten hours, and you
want over 10 times this current


martin
 
forget about PP3 9V batteries, they are unsuitable.

From the Duracell MN1604 datasheet:

Rated capacity 580mAH.
At just 25mA load the volts drop to about 7.5V in ten hours, and you
want over 10 times this current

martin

A great opportunity to do my 9V battery rant. Never design anything
that needs a 9V battery. Use a DC/DC if you have to. OK, there are
exceptions, notably if the current required is near the self-discharge
of the 9V battery.

Long live the AA cell.

Back to the LED question, the experiment would be to power one series
pair, then two, three, etc and watch the source impedance of the 9v
battery become part of the equation.

Back to the rant, two AA cells are about the same size as one 9V
battery. AA cells are about 2.5AH. Now granted, alkalines drop their
voltage linearly, but as a figure of merit, do this comparison:
9x.58=5.22
3*2.5=7.5
so you get 40% more operating time. AA cells can easily be purchased
for under 25 cents, while it is hard to get a 9V battery for less than
a buck. So you get 40% more operating time at 1/4 the price.
 
M

martin griffith

Jan 1, 1970
0
On 30 Mar 2007 14:04:29 -0700, in sci.electronics.design
chomp

Long live the AA cell.

ARGHH wimp republican stuff

checkout the F cell from GP batts
GP1300FH

monster stuff, but can't be charged in one hour, the cables will melt


martin
 
A

alokw

Jan 1, 1970
0
Okay, so it sounds like everyone pretty much agrees that I shouldn't
use 9V batteries. So... what would you all recommend? Should I just
pick up some of those 4x AA battery holders and use those?

Anybody have any idea what the mAh on a standard AA would be like? I
mean - will they be able to drive 50+ LEDs at the required voltage and
mA?

Or... would it be better to go with something like the F cell from GP
that martin recommended? I do need to keep costs as low as possible,
but I'll do what's best.

Thanks a lot for your replies, guys!
 
M

martin griffith

Jan 1, 1970
0
Okay, so it sounds like everyone pretty much agrees that I shouldn't
use 9V batteries. So... what would you all recommend? Should I just
pick up some of those 4x AA battery holders and use those?

Anybody have any idea what the mAh on a standard AA would be like? I
mean - will they be able to drive 50+ LEDs at the required voltage and
mA?

Or... would it be better to go with something like the F cell from GP
that martin recommended? I do need to keep costs as low as possible,
but I'll do what's best.

Thanks a lot for your replies, guys!
Just found the F cell today, havent got a price, but it may be worth
looking at 12V lead acid motor bike batteries.
But you havent said how long you want the leds to stay on for, 1 hour,
10 hours etc.

zz need sleep, bye


martin
 
A

alokw

Jan 1, 1970
0
Hey all!

Thanks for the reply. These LEDs are for a theatre production. They
have to stay on each night for about 1 minute and theres about 20
performances. If I can power them for 45 minutes on one battery, I'll
be happy.

The LEDs are also installed inside hats, so there's not a lot of room
to place a big lead acid battery. I'd like to stay smaller than around
8 cubic inches or so (they're top hats).

Thanks! Let me know if there's any other info that might be helpful. I
really appreciate your help!
 
C

Chuck Olson

Jan 1, 1970
0
alokw said:
Hi all,

I have a quick question that should be simple to answer.
I have 54 LEDs that require 3.4 V DC with a maximum of 30 mA that need
to be wired together.
I have 9V batteries to power them.

I did the calculations and ended up wiring them in series of 2 LEDS
with an 82 ohm resistor for each pair and hooked up the end to a
single 9V battery. With the 27 pairs, it was suppsed to draw 810 mA.

When I switched it on, everything was dim. I didn't think about how
many mA the battery could provide.

My alternative idea is to wire 2 9V batteries together and wire 55
LEDs in series of 5 LEDs with a 39 ohm resistor with each series. This
*should* draw 330 mA. Right?

I think this will work, but want to verify it with you people that
know what you're doing before I buy more 9V batteries and new
resistors. I just want all the LEDs to be as bright as possible.

Thanks for your help!

The Flashlight Manufacturers in China are doing this by paralleling 52 LEDs
and driving them with three AA cells in series and not a single resistor
anywhere (except, of course the internal resistance of the cells and the
LEDs). But of course, they have control over the LED manufacturing process
and can assure that all the LEDs have about the same forward voltage drop so
that current hogging is minimized. I'm also amazed at the color temperature
match they are able to achieve within each flashlight. Maybe this all comes
about through automated testing and binning of raw LED manufacturing output,
but for instance, a complete 32 LED flashlight with three AAA cells in
beautiful anodized aluminum winds up costing the end user just $9.50
(probably less if you buy it at the monthly Electronic Flea Market in
Cupertino CA - - See this vendor's website
http://www.ledwholesalers.com/store/index.php?act=viewCat&catId=20). It
hardly pays to mess around with LEDs in a do-it-yourself effort any more.

If you have an LED set that's not well controlled for forward voltage, then
you're probably going to have to use resistors and higher voltage, probably
losing some power in resistor dissipation. I'd go for the inexpensive
finished flashlight instead. But if what you're planning involves a
non-standard configuration, than I would still order a finished flashlight
and just grab the matched LEDs out of it in order to avoid using resistors.

Good luck

Chuck
 
A

alokw

Jan 1, 1970
0
Thanks for the reply.

Unfortunately, this is kind of a custom rig, and we do require the use
of LEDs that we purchased from a special retailer. They are super
bright 12000 mcd white LEDs that run at a typical voltage of 3.4 V and
no more than 30 mAh. We have 9 hats and each hat requires somewhere
between 35 and 65 of these LEDs.

I have another question. I did some research and found these lithium
9V batteries at Radios Shack, which advertise 2000 mAh. So I picked
one up, and hooked it up to the configuration that I described in my
original post (54 LEDs, 27 pairs w/ 82 ohm resistors on each pair).
Only about 10 of the LEDs were at their full intensity!

I was baffled by this, because I figured, if the LEDs were pulling 800
mA, the 9V battery should be able to supply it in full capacity,
right? It made sense that my normal alkaline batteries dimmed because
they pushed under 600 mA, but these lithium ones were pushing the full
load in theory. Am I totally misunderstood on the concept of
electricity? Can anyone explain this to me? It seems like I'm
providing the LEDs with more than enough power, but they're still
dimmed - I'm sure it just comes down to the fact that I don't know
what I'm doing - but I'm going to keep trying anyways - with your help
of course!

Thanks again for your help!
 
J

Joel Kolstad

Jan 1, 1970
0
alokw said:
Unfortunately, this is kind of a custom rig, and we do require the use
of LEDs that we purchased from a special retailer. They are super
bright 12000 mcd white LEDs that run at a typical voltage of 3.4 V and
no more than 30 mAh.

I think you mean "mA", not "mAh" -- the first (milliamp) is a measure of
current, the second (milliamp-hour) is current integrated over (multipled by)
time.
I was baffled by this, because I figured, if the LEDs were pulling 800
mA, the 9V battery should be able to supply it in full capacity,
right?

Do you have a multimeter? Have you measured the current going through each
LED string? Depending on the battery itself, it may or may not have been able
to deliver 800mA. A cheapy carbon-zinc 9V generally can't (without
significant voltage drop), whereas a NiCad can -- I'm not sure about lithium
cells.

Note that the battery being 2000mAh has nothing whatsoever to do with whether
or not you can (readily) draw 800mA from it. What it *does* tell you is that,
assuming you *do* draw 800mA from it, it'll last approximately
2000mAh/800mA=2.5 hours.
 
D

DJ Delorie

Jan 1, 1970
0
mAh != mA

A battery's milli-amp-hour rating is a measure of total energy, not
the maximum current. For example, a 2000 mAh 9v battery might only be
able to push 20mA, but for 100 hours (20 mA * 100 h = 2000 mAh) (for
example). A "D" cell with the same capacity (2000mAh) might be able
to push 2000 mA for 1 h (2000 mA * 1 h = 2000mAh).

What you want is *peak* current. Bigger batteries offer more peak
current, with 9v being the least (no matter what the mAh is) and D
cells being the most (of the corner-store type batteries). Mostly
this is due to internal resistance; the resistance of the battery
itself is acting like an additional resistor in series with your LEDs,
reducing the current.
 
A

alokw

Jan 1, 1970
0
Thanks again for all of your replies!

That makes a lot of sense. I did indeed mean that each of the LEDs
require 3.4 mA, not mAh. I think you're also right about the 9V not
being able to provide enough "peak current" (look at how much I'm
learning!).

After some more research I came up with this: What if I use a total of
(16) AAA batteries in each hat? This would provide around 24V and I
could wire 56 LEDs in series of 7 LEDs with a 6.8 ohm resistor with
each series. This *should* use 240 mA. Assuming the AAAs give 1250 mAh
(from Energizer's site), they should last 5 hours. This is all under
the assumption that they will be able to provide at least 240 mA of
peak current.

So, does that sound like a smart way of going about this project? I
can get all of the batteries and holders for them for under $80, so
the price isn't terrible. Also, how do I know what peak current a
battery can supply? Can i be sure that the AAAs will provide at least
240 mA?

If I'm still being an ignorant idiot, just say so. I just have to get
this done quick, right, and at a reasonable price - and all those LEDs
have to light up real bright.

Thanks so much for your help!
 
Okay, so it sounds like everyone pretty much agrees that I shouldn't
use 9V batteries. So... what would you all recommend? Should I just
pick up some of those 4x AA battery holders and use those?

Anybody have any idea what the mAh on a standard AA would be like? I
mean - will they be able to drive 50+ LEDs at the required voltage and
mA?

Or... would it be better to go with something like the F cell from GP
that martin recommended? I do need to keep costs as low as possible,
but I'll do what's best.

Thanks a lot for your replies, guys!

I know nicads are very low impedance. NiMH is a bit higher, but still
better than alkaline cells. You would have to check, but I recall a
nicad AA cell is around 30mOhms. The advantage to nicads is that while
the initial voltage is lower (1.25 versus 1.5V), a nicad hangs in
around 1.2V until it is exhausted, then it dies quickly. So not only
is the impedance lower, but the voltage will be better regulated. I
don't think I ever pulled more than 200ma from AA cells, so I don't
know how well your circuit will react, but give it a shot.

BTW, 30ma sounds high for continuous operation (i.e. non-pulsed).
 
E

ehsjr

Jan 1, 1970
0
alokw said:
Hey all!

Thanks for the reply. These LEDs are for a theatre production. They
have to stay on each night for about 1 minute and theres about 20
performances. If I can power them for 45 minutes on one battery, I'll
be happy.

The LEDs are also installed inside hats, so there's not a lot of room
to place a big lead acid battery. I'd like to stay smaller than around
8 cubic inches or so (they're top hats).

Thanks! Let me know if there's any other info that might be helpful. I
really appreciate your help!

5 or 10 alkiline cells. The better solution is 10
cells. Both are described below. First, the 5 cell:

5 alkaline AA 7.5 volts - enough for 28 strings of 2
LEDs at 6.8 plus a 24 ohm resistor per string. With 28
strings at ~29 mA per string, that's a total of ~816.6 mA.
If you can't add an LED to get 56 LEDs, your last string
would use a ~137 ohm resistor (made with a 1500 ohm in
parallel with a 150 ohm). Energizer AA is rated at 2850
mAh under light load, and 1500 mAh at 500 mA discharge.
Since you are almost double that, figure ~ 750 mAh and
you need ~ 570 mAh for 45 minutes.

Give yourself a 50% margin - replace the cells after
10 performances, and you should be good for 20 performances
with room to spare. If you consider the 5 cells together as
1 battery, it meets your "happy criterion", but why chance it?
Buy 10 cells and be safe.

The 10 cell solution: If you have room for 10 cells, you
can reduce the number of strings to 14, using 4 LEDs and
a 40 ohm resistor per string. If your last string has to
have 3 leds instead of 4, it will need a 160 ohm resistor.
Current draw in that configuration will total 420 mA, and
your cells are rated at about 1500 mAh with a 500 mA draw,
so you're golden for 45 minutes of run time across the 20
performances.

The performance numbers for the Energizer are found here:
http://data.energizer.com/PDFs/E91.pdf

Ed
 
E

ehsjr

Jan 1, 1970
0
ehsjr said:
can reduce the number of strings to 14, using 4 LEDs and
a 40 ohm resistor per string. If your last string has to
^^ 47

Should be 47

Ed
 
E

ehsjr

Jan 1, 1970
0
alokw said:
Thanks again for all of your replies!

That makes a lot of sense. I did indeed mean that each of the LEDs
require 3.4 mA, not mAh. I think you're also right about the 9V not
being able to provide enough "peak current" (look at how much I'm
learning!).

After some more research I came up with this: What if I use a total of
(16) AAA batteries in each hat? This would provide around 24V and I
could wire 56 LEDs in series of 7 LEDs with a 6.8 ohm resistor with
each series. This *should* use 240 mA. Assuming the AAAs give 1250 mAh
(from Energizer's site), they should last 5 hours. This is all under
the assumption that they will be able to provide at least 240 mA of
peak current.

They'll last *way* less than an hour. As the
discharge rate goes up, the mAh rate goes down.
At 25 mA discharge, they'll provide 1250 mAh.
But at 240 mA discharge, the mAh rating looks like
it's about 500 mAh. And the voltage decreases
to .8 in those ratings. With 7 LEDs in series,
you can't really afford any drop in the cells. You
have only .2 volts above the 23.8 the LEDs need -
that's only .0125 volts per cell that you can
afford to drop, and cell voltage drops rapidly.
So, does that sound like a smart way of going about this project? I
can get all of the batteries and holders for them for under $80, so
the price isn't terrible. Also, how do I know what peak current a
battery can supply? Can i be sure that the AAAs will provide at least
240 mA?

If I'm still being an ignorant idiot, just say so. I just have to get
this done quick, right, and at a reasonable price - and all those LEDs
have to light up real bright.

Thanks so much for your help!

You are neither ignorant nor an idiot. To be ignorant,
you need to ignore something you know - and this is not
your area of expertise, so you are simply unfamiliar
with it. And far from being an idiot, you are checking
first to look for the pitfalls, rather than charging
forward blindly, as an idiot might do.

Love to see a picture of one of the top hats when
you're done!

Ed
 
W

Werty

Jan 1, 1970
0
Harbor Fright 18vdc , $10 on special
but get the 1.8ah , not the smaller one .

White LEDs are .02 amps , for highest
eff' . DONT RUN AT .03 amps .

LM431 and some parts to make a flyback
to drive any voltage you need .
Flybacks need low inductance , or the
frequencey is too low .
Start with less than .001 Henry , more than
10 microHen'

I just saw a nice MOSFET to drive it ..

only $.10 each .
PMN45EN , Id=1.8 amps @ Vgs =2.5 v .
about .05 Rds .

BTW , anyone into ARM s/w ?
 
A

alokw

Jan 1, 1970
0
Hi everyone, Thanks again for all of your very helpful replies!

I looked over everything you all said and did some thinking. I like
Ed's (10) AA battery solution and I'm pretty sure we have the space
allowance in the hats for them. However, before I commit to purchasing
the battery holders, resistors, batteries, and such, I want to be sure
that the AA batteries will be able to push 500 mA of consistent
current - I can't have these guys going dim on me. I wasn't able to
find the maximum peak current on any battery manufacturer's web sites.
Do you all know for a fact that 10 AAs can push at least 500 mA?

In response to Werty's post, I checked out Harbor Freights web site,
but the only 18vdc batteries I found were drill batteries. If these
are what you were referring to, they definately won't work, just due
to their size and weight. I've listed the exact specs of the LEDs we
have below.

Emitted Colour : WHITE
Size (mm) : 5mm T1 3/4
Lens Colour : Water Clear
Peak Wave Length (nm) : N/A
Forward Voltage (V) : 3.2 ~ 3.8
Typical Voltage (V) : 3.4
Reverse Current (uA) : <=30
Luminous Intensity Typ Iv (mcd) : Average in 13000
Life Rating : 100,000 Hours
Viewing Angle : ±10°
Absolute Maximum Ratings (Ta=25°C)
Max Power Dissipation : 80mw
Max Continuous Forward Current : 30mA
Max Peak Forward Current : 75mA
Reverse Voltage : 5~6V
Lead Soldering Temperature : 240°C (<5Sec)
Operating Temperature Range : -25°C ~ +85°C
Preservative Temperature Range : -30°C ~ +100°C

Should I really try to run these at 20 mA as opposed to the 30 mA that
I've been calculating for?
I also didn't quite understand the other solutions you suggested. I
googled LM431 and found Shunt Regulators, but I'm not sure how I would
go about using one of these. I think the whole shunt and MOSFET idea
is a little beyond me. If there's a really good tutorial of how to use
these online somewhere, it might be more feasible, but given my
current knowledge level, I'd be more comfortable sticking with using
LEDs, resistors, and batteries.

Thanks again for all of your helpful replies and your knowledge! I
couldn't do this without your help!
 
Thanks again for all of your replies!

That makes a lot of sense. I did indeed mean that each of the LEDs
require 3.4 mA, not mAh. I think you're also right about the 9V not
being able to provide enough "peak current" (look at how much I'm
learning!).

After some more research I came up with this: What if I use a total of
(16) AAA batteries in each hat? This would provide around 24V and I
could wire 56 LEDs in series of 7 LEDs with a 6.8 ohm resistor with
each series. This *should* use 240 mA. Assuming the AAAs give 1250 mAh
(from Energizer's site), they should last 5 hours. This is all under
the assumption that they will be able to provide at least 240 mA of
peak current.

So, does that sound like a smart way of going about this project? I
can get all of the batteries and holders for them for under $80, so
the price isn't terrible. Also, how do I know what peak current a
battery can supply? Can i be sure that the AAAs will provide at least
240 mA?

If I'm still being an ignorant idiot, just say so. I just have to get
this done quick, right, and at a reasonable price - and all those LEDs
have to light up real bright.

Thanks so much for your help!

No no no no no! Death to the AAA battery. It is nearly as bad as the
9V battery in terms of economics. AA cells are your biggest bang for
the buck. The maH capability of a battery is a function of volume. The
AA and AAA cells are the same length, but the AA cell has a larger
diameter. The volume increases as the square of the radius, so a
little more radius means a lot more capacity.

The resistor represents wasted power, so I can see why you are going
for more cells in series, but stick to AA cells. I still think you
should try AA nicad cells. Since you have the LEDs on hand, it will be
a simple experiment.

http://www.batterystore.com/Sanyo/SanyoPDF/KR1100AAU.pdf
These Sanyo AA cells are only 19mOhm.

There are discharge curves on the datasheet. I'm not sure what the
"lt" or "It" unit means, but I think the 1It discharge curve is at
1100ma. Often in batteries, you refer to the current as a function of
C, the cell capacity. That is, If you charge 1100ma for 1 hour, you
have a capacity of 1100maH. [Technically this is not correct as the
efficiency of charging isn't 100%. You can see the charge conditions
are 110ma for 16 hours, not 10hours, as would be the case for 100%
efficiency.) Thus I'm guessing the 1It rate is 1100ma. The battery
holds up for about 50minutes at this rate.
 
A

alokw

Jan 1, 1970
0
Hi everyone,

Today, I took some of your suggestions, and decided on trying out a
(8) AA version for a hat requiring only 24 LEDs.
I wired 8 series of 3 LEDs with the same 82 ohm resistors I already
had, which theoretically allowed 25 mA through the LEDs (I compromised
between the 30 mA I was using, and the 20 mA that was suggested). I
used 8 AA batteries because I was able to buy a prebuilt 8 AA holder
from Radio Shack. At 25 mA, in total it used only 200 mA.

Overall, I was pleased with the results. I posted a picture here:
http://www.alokw.com/hats/hats.jpg
The only thing that might become a problem is the weight of 8 AA
batteries. It's a bit heavy and may hinder the actors movement with
the hats. I'm going to run this by the costume folk and see what they
think.

Now, assuming the costume department will be okay with the weight,
would I be safe to use 8 AA batteries to run as many as 66 LEDs? That
*should* draw 550 mA at 25 mA per LED. Is this okay? Also, should I
keep using resistors to keep the current at 25 mA? or should I stick
with 20? or 30?

Thanks for all of your help again guys. I wouldn't be able to do it
without you all.

I have another unrelated question. I hooked up my micrometer to the
leads on the 8 AA battery holder to check how much current it was
pushing. I set it to 10A and the display read somewhere around 1.200.
Does that mean it pushes 1200 mA? The snaps on the battery holder also
started smoking. Does that mean I was drawing too much current for the
battery holder to handle? or the snaps? or something else?
Also, I hooked up each of the micrometer leads to an end on one of the
LEDs while it was turned on to try to check how much current it was
actually getting. I assume I did something wrong here, because the
display said 0.05. How would I go about checking this correctly? Or
did I do something else wrong?

Thanks so much everyone!
 
Top