1 Watt UHF Amplifier schematic wanted

[Diego Stutzer]

Hi again,
I'm looking for a schematic of a uhf-amplifier with a gain of about
10. It shoud give about 1 W output power (to a 50 Ohm Load) at about
100mW input at the (preferably 50 ohm) input (impedance).
The frequency to be amplified is about 440-450 MHz.
Please post links to circuits matching my requirements and generally
all uhf-amplifier design related links here or send me schematics via
e-mail: [email protected]

Thanks in advance.
D. Stutzer

 

[Lizard Blizzard]

Hi again,
I'm looking for a schematic of a uhf-amplifier with a gain of about
10. It shoud give about 1 W output power (to a 50 Ohm Load) at about
100mW input at the (preferably 50 ohm) input (impedance).
The frequency to be amplified is about 440-450 MHz.
Please post links to circuits matching my requirements and generally
all uhf-amplifier design related links here or send me schematics via
e-mail: [email protected]

NOFRICKINGWAY. It's considered rude to ask for replies by email. Shows
you're too fricking lazy to check back in the newsgroup for replies.

Thanks in advance.
D. Stutzer

--
----------------(from OED Mini-Dictionary)-----------------
PUNCTUATION - Apostrophe
Incorrect uses: (i) the apostrophe must not be used with a plural
where there is no possessive sense, as in ~tea's are served here~;
(ii) there is no such word as ~her's, our's, their's, your's~.

Confusions: it's = it is or it has (not 'belonging to it'); correct
uses are ~it's here~ (= it is here); ~it's gone~ (= it has gone);
but ~the dog wagged its tail~ (no apostrophe).
----------------(For the Apostrophe challenged)----------------
From a fully deputized officer of the Apostrophe Police!

<<Spammers use Weapons of Mass Distraction!>>

I bought some batteries, but they weren't included,
so I had to buy them again.
-- Steven Wright

FOR SALE: Nice parachute: never opened - used once.

(Problem) Evidence of leak on right main landing gear
(Solution) Evidence removed

F
o
d
d
e
r

f
o
r

s
t
u
p
i
d
"
n
o
t

e
n
o
u
g
h

i
n
c
l
d
u
d
e
d

t
e
x
t
"
e
r
r
o
r

m
s
g
..

 

[Allodoxaphobia]

e-mail: [email protected]

Ha!
So, maybe you think the spam harvesters will ignore your
un-munged From: in your posting?
|From: [email protected] (Diego Stutzer)
Ha!
Your INBOX is toast.

Jonesy

 

[YD]

Hi again,
I'm looking for a schematic of a uhf-amplifier with a gain of about
10. It shoud give about 1 W output power (to a 50 Ohm Load) at about
100mW input at the (preferably 50 ohm) input (impedance).
The frequency to be amplified is about 440-450 MHz.
Please post links to circuits matching my requirements and generally
all uhf-amplifier design related links here or send me schematics via
e-mail: [email protected]

Thanks in advance.
D. Stutzer

Google

- YD.

 

[Steve Roberts]

www.rfparts.com

buy a motorola or similar RF module. aka a "CATV Brick" or "CATV
AMP".

cost 60-90$ US.

usually runs off 12 or 24 volts, and get the app note/manufaturers
data from RF parts

make sure you have a good RF wattmeter and adjust the source before
the amplifier to avoid overdrive. overdrive is BAD. It will need a
heatsink!

if your really transmitting with it, put a filter on the output as
many of those modules have bandwith from 0 to 550 mhz or so. The law
says any harmonics and spurs you generate must be about 40 Db down
from your output


time spent building anything else without the proper equipment,is
priceless, and judging from the language in your post, you dont have
the skills/milliwatt meter to do it.

Dont expect this fowarded via email.

Steve Roberts